More
Strippit Machines & Tooling For-Sale!
This Page is a Continuation of our Main
WebPage as we had Too Many Items For-Sale to Fit on The First Page.
Please make sure you see That Page Also!
Strippit Custom 18/30 Punch Machine
30 Ton Punching-Force, Good Running Condition, s/n 3066976
Has BOTH 1 1/4" AND 3 1/2" Swing-Arm Tool Holders that many Machines Lack!
And we will include the LIKE-NEW 3 1/2" Punch-Holder shown below!
Strippit sells just 3 1/2" Swing-Arm Holder
& Punch Holder for $6600.00 !!!
We are selling the Custom 18/30 Machine
AND 1 1/4" Swing-Arm Holder
AND 3 1/2" Swing-Arm Holder
AND 3 1/2" Punch-Holder
All for just $4500.00 !!
This page was last updated on: August 15, 2024
Very Rare Strippit
5 Inch Punch Tool Holders
For Strippit
FC1250/45/51, FC1250/45/72,
FC51/30, and FC51/40
Turret Machines in the Big 5 Inch Station #1
Also Strippit Single-Station Machines; Super 30/40, Super 30/40 AG, Super 750, and Super 750 AG
Machine Technologies Co.
Strippit Mechanical & Electronic Repair Parts
and
Strippit HECC80 CNC-Control Machine Repair Service
and
General Electric Hi-Ack Servo Drive Parts & Repairs
Phone 704-233-5229
For All You Guy's that have Managed to Break o r Lose
Your 1 1/4" & 3 1/2" Swing-Arm Tool Holders,
We can Supply Brand-New STEEL Swing-Arm Holders.
Old Strippit Iron 1 1/4" Holders Will Break-In 2 when they Fall-Off Table onto Floor,
and Buyers of Used Machines Never Seem to get Both Holders!
Ours Are Steel, Not Brittle Cast-Iron
That Strippit Has Been Selling Since The 1950's.
New Holders are Not Cheap. But if you have a
Custom 18/30, Custom 30/30, Super 30/30, Super 30/40
Sonic 18/30, or Similar Single-Station Strippit Machine,
you have Got To Have Holders if you Want To Punch Holes!
We are Looking to Buy
Old Strippit FC1000/3 Machines, Running or Not!
We also sometimes Buy
Old CNC Controls and Old Machines,
just to Scrap-Out for the Parts,
Call us on What you have!
We are looking for 1 Inch-Wide Fan-Fold Punch-Paper,
which was used to
Load Paper-Tape Programs into Old NC Control Machines.
Strippit Imported Power Notcher from Italy in 1980's,
Painted "Strippit" on it to
Magically Became
"Strippit Notch-Rite". But, In that Special Strippit Way, Strippit has Abandoned Them, with No Service & No Parts Available. Picture is for
Reference, We do Not have
a Notch-Machine For Sale!
We Do Have 1 Brand-New Set of 4 Hi-Carbon Steel
(2 Upper & 2 Lower)
Shear-Blades For-Sale for this Handy Machine. Set of Blades is Shown Below.
NEW
Old--Stock
4 Blade Set
for Your
Strippit
Notch-Rite
Machine!
Buy Them Now
Because When These are Gone,
We will NOT
be getting
any More!
Strippit
Part #18427-000
We have Just
This 1 Set
For-Sale
Brand-New
STEEL
3 1/2" Swing-Arm
Punch Tool-Holder Assembly
Complete as Pictured
at Left, Ready for Your
Super 30/30,
Custom 30/30,
Super 30/40,
Sonic 18/30,
or Custom 18/30
Strippit Machine
For-Sale
Brand-New
1 1/4" Swing-Arm
Punch Tool-Holder
Assembly
Complete As Pictured
at Right, Ready for Your
Super 30/30,
Custom 30/30,
Super 30/40,
Custom 18/30,
or Sonic 18/30
Strippit Machine
A Pair of Good Used
Original Strippit
Short Workclamps
for
FC1000/1,
FC1000/2,
FC1000/3,
FC750, FC750/2,
Machines.
Allows 9 Inch Wider Sheets
to be Processed
on these Machine.
Can also be used on
FC1250/30/1500
to allow
11 Inche Wider Sheets!
"Chance"
Warner's Chancellor
1/8/1993 --- 11/15/2006
"Bandit" Also known as "The Hell-Bitch"
in Hot-Pursuit of
Cisco, our Little 100+ lbs. Red German Shepard Pup,
It's Good to be Our Dogs.
Click Button at Left for Super 30/30 and other Strippit Single-Station Machine Info!
Wilson
3 Inch
Louver
Tool Set
Most of these Punches shown here are Sold.
BUT,
I Still have some
2" x 2" Dies
with Assorted
Die Clearances,
+.006,
+.008,
+.012,
+.037,
+.050,
+.068,
Etc.
many of these Dies are
Never-Used
and
Brand-New.
Strippit and Wilson
For 1 1/4"-Stations, The Hard-To-Find
1 1/4" Drop-In Punch-Holders for 1/2"--Shank Punches
and with Included Head-Nut
and
1 1/4" Drop-In Punch-Holders for 5/8"--Shank Punches
and with Included Head-Nut
These all go into Standard 1 1/4" Stations
on Single-Station Machines And in Turret-Machines
1.000"
Heavy-Duty
Nibble-Tool
Punch
and
+.012" Clearance Die
.250" x 1.000" Punch Assembly and
+.012" Clearance Die
and
.250" x 1.125" Punch Assembly and
+.006" Clearance Die
Rare Strippit
3 1/2" Alignment and Indexing Tool Set.
Top-Tool's Dowel-Pins Mate with Lower-Tool's
Hardened-Bushings for
Lasting Durability and Accuracy.
And this is the ONLY Tool Set that has the
360 Degrees Etched into Lower-Piece for
Precise Angle Setting!
Click-On
The
Yellow--Buttons
For
More Information!
"Bandit"
3/1996 --- 12/1/2009
The Strippit "Notch-Rite" Saga
In early 1980's Strippit Sold Notcher Machines made here in USA by Sister Company Di-Acro, which was also owned by Houdaille Industries. Di-Acro Notchers used 4 Rectangle Blades that could be Flipped 4-Times to give you 4 Edges before needing Sharpening, like any Good Shear Machine.
Then, Wall-Street KKR & Houdaille Killed Di-Acro, so Strippit Imported these Notch-Rite Machines from Italy. Not bad Machines, but for Unknown Reason, All 4 Blades had Goofy Angles & Curves
so you could Not Flip them 4 Times. Blades for this Italian Machine are Shown Below.
In Strippit's Quest to ever make Machines Cheaper, Production was Moved again to Taiwan China.
Machines were similar, but somehow, design was changed for 3rd time. Blades are Sorta Rectangular, but are Different from other 2 types, how Stupid. To try and Help 1 of Strippit's Own Customers, I Talked to Strippit about these Machines & Parts, but Strippit Was Clueless!
As there is No Parts & No Service & No Support from Strippit (Now LVD) on these Machines,
I would get my 5-Cents a Pound at Scrap-Yard for them and Buy a
Good German Boschert Notch Machine with a Extra Set of Blades. There are also
Gun Control
Rare Strippit
Thin-Turret 3 1/2" Alignment Tool Set
Make Sure Your Blades Match These When Ordering!
Also, When Sharpening,
Top-Blades are Ground on the Lower (Narrow) Edge,
Lower-Blades are Ground on the Top (Wide) Edge.
If you Sharpen Blades Incorrectly, You will Ruin Your Blade Set!!!
4 1 1/4 Inch Punch-Tool Sets
All 4 Sets are New or in Excellent Condition
From the LEFT on 2 Photos Above;
Wilson Tool Co. #54-8457 Progressive .500" x .900" Ribbing-Tool
Used to Add Stiffing Ribs to Sheetmetal Parts
Fully-Guided .218" x .875" Obround Punch
and +.012" Die
Fully-Guided .625" Square Punch
and +.012" Die
.810" Square Punch
and +.010" Die
Take Your Pick! $20.00 a Set!
"Cisco"
12/08/06 --- 09/12/13
"Kira"
The Bear Hunter
Kira's a Hi-Energy
which are Fearless
Bear & Boar Hunters,
With a Little
Pit-Bull Mixed-In Just to
Calm-Her-Down a Little.
We Rescued her from a
Kill-Shelter 02/01/14
Kira,
Off-Duty at Left,
Now Provides
Our Office Security.
Wilson 4" x 1" Louver Tool Set
New Never-Used Condition!!!
TWO 3 1/4" x 3/8" Louver Tool Sets
--- Some Wear in Punch-Holders,
--- Both Top-Dies look Very-Good Condition
--- 1 Bottom-Die looks in Very Good Condition
--- Other Bottom Die might need some work
Take BOTH SETS (4-Pieces) for 1-Money $350.00!
This page was last updated: August 15, 2024
5 STRIPPIT 3 1/2 Inch Stripping-Guide Punch-Holder Assemblies in Like-New Condition
Quick-Release No-Tools Stripper-Plate Release!
Just Push-Down Button & Twist to Release Retaining-Ring & Stripper-Plate!
I am Selling You the 3 1/2" Stripping-Guide Punch-Holder Assembly
Any Installed Punch-Tool & Stripper-Plate & Dies are Free Extra Add-Ons!
For-Sale
Refurbished
1 1/4"
and
3 1/2"
Swing-Arm
Punch Tool-Holder
Assembly
Complete
as
Pictured at Left
Ready for Your
Super 30/30
Custom 30/30
Super 30/40
Super 30/40HD
Sonic 18/30
Custom 18/30
Strippit Machine
NEW
Strippit & Amada
Thick-Turret Size D 3 1/2" Alignment Tool Set
